Hyundai How to Access SRS Codes 

On some older Hyundai SRS systems the SRS codes can be accessed by jumping PINs # 2-SRS and 12-ground. Use a test light as the jumper wire if in doubt. WARNING! Jumping these 2 wires may short out the SRS module on some model year. On the rest of the systems a scanner is needed to access codes. Do not jump OBD 2 pins. For the most part an aftermarket scan tool can access most Hyundai SRS codes. Connect the scanner and follow procedures. 

------------------------------------------------------------------------------

KIA All Models

How to Access SRS Codes 

KIA Motors 

Accessing Diagnostic Trouble Codes without a scan tool

To access and read SRS DTCs, proceed as follows:

1. Turn ignition On and observe air bag lamp operation.
2. If lamp lights from 4-8 seconds and goes off, SRS is operating properly.
3. If lamp does not light, there is a fault to the light circuit. Repair as needed.
4. If lamp remains lit or flashes, on 1995-97 models, turn ignition Off, then proceed as follows:

a. Locate Data Link Connector (DLC) in engine compartment.
b. On Sephia models, install jumper wire between pins six (ADU) and 12 (G2), PRESS THE DIAGRAM BUTTON BELLOW.
c. On Sportage models, install jumper wire between pins fourteen (ADU) and 12 (G2).
d. On all models, turn ignition On and record any DTCs indicated by air bag lamp.

5. If lamp remains lit or flashes, on 1998-2006 models, turn ignition Off, then proceed as follows:

a. Locate Data Link Connector (DLC) in engine compartment. On some models, the OBD 2 DLC may also work for SRS codes.
b. Connect Kia Power Scan Tool, or equivalent to DLC.
c. Turn ignition switch to On position and record any codes displayed by the scan tool.

Clearing Diagnostic Trouble Codes

1. On 1995-97 models proceed as follows: 

a. Connect a jumper cable to the battery ground. You may also use the DLC ground.
b. Turn ignition On.
c. On Sephia models, touch DLC pin 6 on ADU to ground four times. 
On Sportage models, touch pin 14 to ground four times. 
If grounding cycle is too fast the DTCs may not erase and process may have to be repeated.
d. On all models, turn ignition Off.

2. On some 1997 models DTCs are erased as follows:

a. On Sephia models, install jumper wire between pins 6 (ADU) and 12 (G2).
b. On Sportage models, install jumper wire between pins 14 (ADU) and 12 (G2).
c. On all models, turn ignition On and observe air bag lamp operation.
d. A rapid continuous flashing indicates a pass condition.

3. Remove jumper wire.
4. Turn ignition On and ensure air bag lamp lights for 4-8 seconds, then goes off.

5. On 1998-2002 models, proceed as follows:

a. Locate Data Link Connector (DLC) in engine compartment.
b. Connect Kia Power Scan Tool, or equivalent to DLC. 
c. Turn ignition switch to On position.
d. Follow scan tool instructions to erase diagnostic trouble code.

On most 2000 and up KIA Motor vehicles, a scanner is needed to access codes. 

------------------------------------------------------------------------------

MITSUBISHI ALL YEARS

Accessing DTCs

1. Inspect SRS or Supplemental Restraint System components.
2. Start engine and watch SRS or Supplemental Restraint System warning light.
3. If light lights for seven seconds, then goes off, system is functioning correctly.
4. If light remain illuminated or does not light at all, turn ignition switch to Lock position.
5. Connect a scanner to diagnostic check connector at the fuse box.
6. Follow the scanners instructions. 
7. Record DTCs.

Clearing DTCs

Connect a scanner to Data Link Connector (DLC) and follow scan tool instructions.